RPCL 10ton Commercial Heat Pump Split Unit 230V 3phase
Price only visible to logged in users
Product number:76680
Manufacturer number:RPCL2120CBZ
Other models available
General Information
- Finish
- Baked Enamel
- Number Of Stages
- 2
- Product Group
- 410A Clearance
Air Volume/Air Flow
Compressor
Connections
Description
Electrical
Energy Efficiency/Performance
Material
Measurements
Rated Capacity
Refrigerant
Standards
Product description
All access panels can be opened or removed without affecting the structural strength of the unit stamped louvered panels offer 100% protection for the condenser coil
Lug for field connection of ground wire
The contactor is an electrical switch which operates the compressor and outdoor fans Its 24 V coil is activated on a call for cooling or heating
75 VA step down-type, from Line to 24 V with resettable circuit breaker
Help provide starting torque necessary to boost the condenser fan motors to operating speed by directing their stored energy to the starter winding in step with the running winding
Used when unit is in heating mode to defrost outdoor coil
To provide compressor protection under abnormally high head pressure conditions (outdoor fan failure, restriction, dirty coil and more) or abnormally low suction pressure conditions (restrictions, TEV failure, loss of charge, indoor blower failure and more) while eliminating nuisance tripping sometimes experienced with conventional control systems
Constructed with copper tubes and aluminum fins mechanically bonded to tubes for maximum heat transfer capabilities, all coil assemblies are leak tested up to 550 psig internal pressure
Control box with separate line and control voltages, as well as compressor and other refrigerant controls are accessible through access panels, an electrical access cover may be opened or removed without affecting normal operation of the unit, condenser fan motors are equipped with molded plugs for easy removal, Louver panels and end access panel can be removed for coil cleaning
Galvanized steel with weather-resistant baked enamel finish
The scroll compressor is hermetically sealed with internal high temperature protection and durable insulation on motor windings, the entire compressor is mounted on rubber grommets to reduce vibration and noise
Used when unit is in heating mode and outdoor coil functions as evaporator
Minimizes refrigerant migration to compressor sump
To prevent liquid slugging of compressor
All field sweat joints are made external of the unit and are located close to the ground for a neat looking installation
Standard on liquid line and vapor line
Sized for maximum capacity and efficiency, 24 V coil, energized in heating
Lug for field connection of ground wire
The contactor is an electrical switch which operates the compressor and outdoor fans Its 24 V coil is activated on a call for cooling or heating
75 VA step down-type, from Line to 24 V with resettable circuit breaker
Help provide starting torque necessary to boost the condenser fan motors to operating speed by directing their stored energy to the starter winding in step with the running winding
Used when unit is in heating mode to defrost outdoor coil
To provide compressor protection under abnormally high head pressure conditions (outdoor fan failure, restriction, dirty coil and more) or abnormally low suction pressure conditions (restrictions, TEV failure, loss of charge, indoor blower failure and more) while eliminating nuisance tripping sometimes experienced with conventional control systems
Constructed with copper tubes and aluminum fins mechanically bonded to tubes for maximum heat transfer capabilities, all coil assemblies are leak tested up to 550 psig internal pressure
Control box with separate line and control voltages, as well as compressor and other refrigerant controls are accessible through access panels, an electrical access cover may be opened or removed without affecting normal operation of the unit, condenser fan motors are equipped with molded plugs for easy removal, Louver panels and end access panel can be removed for coil cleaning
Galvanized steel with weather-resistant baked enamel finish
The scroll compressor is hermetically sealed with internal high temperature protection and durable insulation on motor windings, the entire compressor is mounted on rubber grommets to reduce vibration and noise
Used when unit is in heating mode and outdoor coil functions as evaporator
Minimizes refrigerant migration to compressor sump
To prevent liquid slugging of compressor
All field sweat joints are made external of the unit and are located close to the ground for a neat looking installation
Standard on liquid line and vapor line
Sized for maximum capacity and efficiency, 24 V coil, energized in heating
General Information
- Finish
- Baked Enamel
- Number Of Stages
- 2
- Product Group
- 410A Clearance
Air Volume/Air Flow
Compressor
Connections
Description
Electrical
Energy Efficiency/Performance
Material
Measurements
Rated Capacity
Refrigerant
Standards
Product description
All access panels can be opened or removed without affecting the structural strength of the unit stamped louvered panels offer 100% protection for the condenser coil
Lug for field connection of ground wire
The contactor is an electrical switch which operates the compressor and outdoor fans Its 24 V coil is activated on a call for cooling or heating
75 VA step down-type, from Line to 24 V with resettable circuit breaker
Help provide starting torque necessary to boost the condenser fan motors to operating speed by directing their stored energy to the starter winding in step with the running winding
Used when unit is in heating mode to defrost outdoor coil
To provide compressor protection under abnormally high head pressure conditions (outdoor fan failure, restriction, dirty coil and more) or abnormally low suction pressure conditions (restrictions, TEV failure, loss of charge, indoor blower failure and more) while eliminating nuisance tripping sometimes experienced with conventional control systems
Constructed with copper tubes and aluminum fins mechanically bonded to tubes for maximum heat transfer capabilities, all coil assemblies are leak tested up to 550 psig internal pressure
Control box with separate line and control voltages, as well as compressor and other refrigerant controls are accessible through access panels, an electrical access cover may be opened or removed without affecting normal operation of the unit, condenser fan motors are equipped with molded plugs for easy removal, Louver panels and end access panel can be removed for coil cleaning
Galvanized steel with weather-resistant baked enamel finish
The scroll compressor is hermetically sealed with internal high temperature protection and durable insulation on motor windings, the entire compressor is mounted on rubber grommets to reduce vibration and noise
Used when unit is in heating mode and outdoor coil functions as evaporator
Minimizes refrigerant migration to compressor sump
To prevent liquid slugging of compressor
All field sweat joints are made external of the unit and are located close to the ground for a neat looking installation
Standard on liquid line and vapor line
Sized for maximum capacity and efficiency, 24 V coil, energized in heating
Lug for field connection of ground wire
The contactor is an electrical switch which operates the compressor and outdoor fans Its 24 V coil is activated on a call for cooling or heating
75 VA step down-type, from Line to 24 V with resettable circuit breaker
Help provide starting torque necessary to boost the condenser fan motors to operating speed by directing their stored energy to the starter winding in step with the running winding
Used when unit is in heating mode to defrost outdoor coil
To provide compressor protection under abnormally high head pressure conditions (outdoor fan failure, restriction, dirty coil and more) or abnormally low suction pressure conditions (restrictions, TEV failure, loss of charge, indoor blower failure and more) while eliminating nuisance tripping sometimes experienced with conventional control systems
Constructed with copper tubes and aluminum fins mechanically bonded to tubes for maximum heat transfer capabilities, all coil assemblies are leak tested up to 550 psig internal pressure
Control box with separate line and control voltages, as well as compressor and other refrigerant controls are accessible through access panels, an electrical access cover may be opened or removed without affecting normal operation of the unit, condenser fan motors are equipped with molded plugs for easy removal, Louver panels and end access panel can be removed for coil cleaning
Galvanized steel with weather-resistant baked enamel finish
The scroll compressor is hermetically sealed with internal high temperature protection and durable insulation on motor windings, the entire compressor is mounted on rubber grommets to reduce vibration and noise
Used when unit is in heating mode and outdoor coil functions as evaporator
Minimizes refrigerant migration to compressor sump
To prevent liquid slugging of compressor
All field sweat joints are made external of the unit and are located close to the ground for a neat looking installation
Standard on liquid line and vapor line
Sized for maximum capacity and efficiency, 24 V coil, energized in heating